8mm OD 20mm Long Light Load Compression Mould Die Spring Yellow Compression Mould Die Spring for The Ender 3s Bed 20pcs

I bought these because they were recommended online. I have 2 3D printers, and I used these on both of them. I leveled the bed once on each and have not had to level since. Both of my printers have BL Touches, and I run the grid maybe once every two weeks but the mesh is almost exactly the same with these springs.

Springs seem high quality. They were a little longer than I expected. They were easy to install on my Ender 3 clone.

These are better springs, but I still end up leveling the beds often I thought these would eliminate the need to level so often, and they really do not accomplish that They do seem to stay put better than the stock springs though, so it is faster to level than before they do not cost much, so I would recommend these as a worthwhile upgrade, just not a necessary upgrade perhaps

Fit perfectly. A little stiffer that the originals but thats what I was looking for.

I bought these for installation on an Ender 3 print bed, replacing the OEM spring set. These were noticeably stiffer than OEM, meaning the bed is being held more firmly. A tip for Ender 3 users is to trim a turn or so from the spring to be used on the corner with the bed heater feed line. There is a plastic support there that takes up a bit of space. If you use an unaltered sprint, that corners adjustment will max out before the other 3.

These worked as intended, they arrived on time and Im very happy with the purchase. If you are new to 3D printing and getting these to upgrade a printer that you just bought then you might want to hold off until you know whether or not youre going to go with a auto bed leveling system like a BL touch or a CR touch. If youre going to eventually upgrade to a BL or CR touch then you might want to hold off on the bed springs and instead order the silicone spacers. Silicone spacers are just a bit more consistent, in other words once you get the bed adjusted with the silicone spacers You very rarely have to adjust it again as the ABL can compensate for minor deviations. On the other hand with the springs you can throw the bed out of level by simply prying a part off the bed too hard forcing you to re-level the bed.

Be forewarned, this product does NOT fit the Ender 3 S1 Pro, or at least what I received does NOT, they are too short, and when comparing the stock springs, and these, there is about 2-3mm height difference, DO NOT BUY FOR THE ENDER 3 S1 PRO!

I got tired of leveling my hotbed nearly every time I printed something, so I picked these up to try them out. I still seem to be re-leveling my bed quite a bit when printing ABS (perhaps the hotter temps), but these seem to hold the bed level for quite awhile when I am printing with PLA. Definitely worth the few extra dollars to pick up this package to replace the stock springs if you have an Ender 3 v2 or like in my case, the Voxelab Aquila X2.

Perfect for Ender 3d

I got these as a small, inexpensive upgrade for my Ender 3 3D printer and they work perfectly. The stock springs that came with my printer werent exactly bad, but after receiving these I noticed that theyre much stiffer than my original springs; making my print bed much more stable while printing. I would highly recommend these as a small purchase if you own a 3D printer with springs on the print bed such as the Ender 3! Pros: - They couldnt be easier to install! Unscrew the adjustment knobs from the bottom of your print bed and replace those springs with these new ones. Screw the adjustment knobs back into the print bed with these new springs and youre done! Level your bed and keep on printing! :D - Theyre yellow. That could be a pro or a con depending on your preference, but it gives the printer a little more of a performance look to it, in my opinion. It makes the Ender 3 look a little more intricate at the very least. Cons: - Nothing. I got 20 springs in a small bag and they work perfectly for my purpose! I will definitely be buying these again if Im in need of more springs for my printer!