Eastern Jungle Gym DIY Swing Set Hardware Kit with Easy 1-2-3 A-Frame Brackets, Swing Seats, Ring Trapeze Bar and All Assembly Hardware and Instructions - Wood Not Included

This kit was an excellent value and what a great way to cut the cost of a solid swing set at least by half!! You get everything that you need except for the lumber. Really simple to put together.

So i was planing to build a swing set and liked overall ratings for jungle jim products across the board. One of the the points for me was for sure saving some money when buying kit vs buying everything separately. However disappointment hitted right. after opening the box. 1) Frames are not fully painted inside in this kit. They are however if you buy brackets separately. If you planing to use pressure threaded lumber they should be painted to avoid corrosion. 2) Swing hangers are for sure heavy duty, however they dont have plastic washers AND had rust with crumbling paint out of the box. If you buy hangers of same brand separately they do have washers and i have not seen many reviews about rust if at all. 3) All hardware was zinc coated, which is not suitable for pressure threaded wood. If you buy brackets separately they do provide galvanized hardware which is good for PT lumber. Overall browsing reviews for other jungle gym products i saw similar reviews from year or two ago. Lots of recent reviews saying about better hardware and fully painted brackets. Looks like this kits probably were made a while back and do not have all the update manufacturer implemented recently. Overall very good brand. Returned this kit, however ordered everything separately as parts.

The hardware kit appears very heavy duty and proved fairly easy to assemble. I did it by myself but would recommend 2 people, particularly to move to the final location, upright, and level. I used large furniture sliders to move it around on the grass fully assembled. The only thing I might do different is to make the legs using 9 ft. - 4x4s. I bought 8 boards as recommended by Eastern and now wish it were a tad taller. I had to sand the 4 x 6 top beam quite a bit on one end to get it to fit (used random orbital sander). I ended up using a 3 lb. sledge and a large block of wood (to prevent bracket damage) to get that end on. The second end required a bit of sanding but went on much easier. I also recommend a drill with a built in bubble level (mine is a Dewalt) to drill the bolt holes through the top beam for the hangers. I would have given it 5 stars but for the cost.

BUYER BEWARE!!!! You will need to spend more. The hardware that came with it would have been good if it would have all come. Missing hardware!!! Missing 16 lag bolts and washers. Missing the additional 8 needed for the in ground stakes. Even more importantly missing the hardware to actually hang swings to the swing set. For $260 and change one would expect it all to be there, as described ( all lag screws no through bolts as described) I spent another $63.00 for the hardware that was missing. What a disappointment. The two brackets for the 4x4 legs and 4x6 beam look and seem adequate. That being said and after the added expense, it went together relatively easy (heavy work) and looks good. I used a 4x6x12 so I can add a saucer swing to the far end and 4x4x10 so it will sit higher. Took a little over 3 1/2 hours total. Suggestions. Use a carpenters square and drill the holes smaller that instructions tell you, to ensure maximum bite from screws into the wood. I don’t imagine the company with reimburse me for the missing hardware, and I’m not sending it back. Next I’d choose just the brackets and price it all together myself and would prob save close to $100.00 or more plus added cost.

We are 2 months into using the Eastern Jungle Gym Classic Swing Set and love it. We replaced the trapeze for a toddler bucket seat (also Eastern Jungle Gym) for our almost 2 year old. He loves the swing & asks to swing often. I also love it and will swing for hours on end into the night. Assembly was relatively straightforward, but here are some notes: - Check the bolts & nuts. We had a bolt that was bent and went to the big orange store to get a new one. - I personally did not use pretreated wood, because Id read about the dangers of getting a splinter from the treated wood. Instead I used a standard deck stain - That same big orange store cut my 4x4s & 4x6s for me so no need to break out the circular saw. - Make sure to get a long enough drill bit to go through the 4x6. Trying to meet from either end would take a level of skill I didnt even want to attempt. - I was able to assemble the entire swing set by myself, but needed help flipping it over into place

Had it up and swinging in just a couple hours. Picked up the 4x4s and the 4x6 from the local store to avoid shipping it. Comes with more than enough hardware. Its almost like multiple kits thrown into the same box, lots of extras. It comes with the anchors to make it extra stable. Personally, I chose to hit the hardware store again to buy half inch lag bolts, rather than try to use the carriage bolts that come included, that would have required drilling through the 4x6. Everything fits snug, as you may have read, and I had the best luck using the weight of the wood itself, as a pile driver to get the brackets on. Get the brackets on a little, then tip the wood up and pound the bracket onto something solid. Easy enough for a solo job, but highly recommended to have 2+ people stand it up. I did it myself just barely... thats a lot of wood when its all together. I think I saved about $200 or so versus buying a complete kit locally.

This kit built one strong swing set! I used 10 legs and a 12 beam. Assembly was pretty easy with the right tools. I used treated pine. I laid out my hardware pieces on the beam to get a basic sense of spacing. Then, I corrected for uniformity. Basically, the swings are 18 apart from each other and 12 away from the brackets. Because of the lean of the legs, you could get them closer to the brackets without issue, but I liked the look of the spacing. I also left 6 inches of the beam sticking out of one side to install a climbing rope. Then, I chalked out my spacing and started drilling some pilot holes. When using my 3/8s auger bit, I drilled from the bottom, but turned it over to countersink the top. I really recommend doing that. It makes the holes clean and keeps the tops of the bolts flush with the wood. That way, if anyone gets on top, they wont have to deal with metal sticking up. After the bolts were installed, I slid on the brackets. Ive heard others complain about this, but my wood was dry enough. They made a snug fit, but it didnt require any planing or sanding - just a few taps with a rubber mallet. When assembling the legs, I added one side and rested the other side on a ladder. (I did need some help guiding the second set of legs into the brackets, but that was the only time I needed an extra set of hands.) I adjusted the legs, drilled some pilot holes and bolted it all together. Finally, I took a hand planer to the edges to round them out a little and voila! All-in-all, it probably took 3 hours or so. Its so heavy, I didnt feel the need to stake it down. I tested it out with 2 heavy adults and it easily held 500 lbs - even with the longer beam. And because of the weight, there was no risk of tipping it over. Really great product!

This is an excellent kit to build a swing set. EVERYTHING you need is included except the wood and stain. While it calls for a ten foot 4x6 for the cross piece I opted for a 16 footer thinking I was going to add another swing on the outside. But the angle of the legs was too much. So instead I made a 14 foot span for 4 swings (or other options) in between. You wouldnt want 4 adults swinging at the same time but 2 adults and 2 children should be fine. I selected Douglas fir for all of the wood. 1 4 x 6 x 16 for the beam and 4 4 x 4 x 8s for the legs. I sanded every piece, every side with an orbital sander 60 grit. Then I applied a heavy coat of exterior stain. We chose a light stain which turned out just a tad darker then the natural wood. The brackets just barely slid over the 4 x 6 after I pried the sides out a tiny bit. First time I tried they stuck a bit. Just a tiny spread helped the bracket slide on. This was extremely important because I attached the brackets to the 4 x 4 legs first. Then I propped the 4 x 6 on two ladders and slid the bracket with the two legs onto the 4 x 6. Which is why I made sure they would easily slide on! Doing it this way allowed me to see just how the swings would work which is when I realized they would all have to go between the legs. Then I took the legs off and measured and drilled the holes for the brackets that hold the swings. It was easier to drill the holes with it down on the ground. I attached the brackets after I put it back together. I was concerned about the brackets getting in the way when I was lifting it back up. Since I had the extra length I adjusted the measurements of the instructions. The swings on the ends are 20 inches from the outside of the brackets. Considering the legs angle out away from the swings you have 30 or more inches of room between the swing and the legs. Then I put 18 inches between each swing with 18 inches of space for each swing. Again, it was much easier to measure and drill with the beam on the ground. I put it together by myself. The beam wasnt terribly heavy to lift up onto the ladders. I lifted one end on the first ladder and the other end resting on the ground. This made it really easy to slide the the first A (bracket with legs) onto the first end. Then I put the other end onto the other ladder (I had to add about 6 2x4s to get enough height with my ladder). Attaching the other A wasnt too difficult. I just wiggled it onto the beam up to the line I had drawn. Then I drilled the 1/4 inch pilot holes and attached the brackets to the wood with the included lag bolts. The swings are good quality and the chains are coated at the part where you would grab to prevent fingers getting pinched. It only comes with enough brackets for 3 swings so I ordered another set and chair for my fourth. Its easy to attach and un-attach different swings or equipment with the included spring clips. Our grandson loves it and so do we! And it looks great, too!

Be prepared to sand every single post that is supposed to fit into these “easy” brackets. It’s an absolute joke that it takes so much personal labor to get these to work. I have an idea, make the bracket openings a little larger and provide a pack of shims. Dang.