Hakko FX888D-23BY Digital Soldering Station FX-888D FX-888 (blue & yellow)

It was fine but I ended up replacing it with a pinecil, which is less bulky, way more controllable, and has all sorts of cheap tips available.

Great iron. Durable and dependable.

I thought that I was bad at soldering. Turns out I just needed to spend more than $15 on a soldering iron. My only complaint with this unit is that it is a bit harder to change temp than in units with both plus and minus buttons. Not a huge issue as I tend to use one of 2 solders so mostly it is set it and forget it, but it might be nice to have a little more fine control based on what type of job Im doing as well as solder type. I also would have liked to go for one of the newer types that have the heater in the replaceable cartridge tips, but I couldnt justify the cost as a hobbyist.

We have two Hakko 936-12 irons, which we use in a daily production environment. The FX-888 is the updated replacement. Its smaller, but packs a bit more power than the 936. The handpiece is comfortable for day-long use and the new holder incorporates a slot for brass wool (better than a wet sponge), so you dont need a separate tip cleaner. Theres still a sponge plate for traditionalists. Hakko supplies both a sponge and a wad of brass wool. The thermostatic control is accurate and the iron heats quickly. More important, the more powerful 70W ceramic element brings the tip back up to temperature quickly when you heat a large surface, and the internal thermostat prevents overshoot. In other words, the Hakko maintains your chosen working temperature, making it easier to do clean, consistent work. Using brass wool to clean the tip causes less thermal shock than water does and theres essentially no thermal recovery time. The supplied screwdriver-shaped tip is small enough for standard printed-circuit board work and can also lay down enough heat to attach a braided ground to the back of a potentiometer. The silicone-coated cable on the handpiece withstands occasional accidental contact with the tip or barrel without damage. The brightly colored components are a departure from the usual somber black, looking like they could have been made by a toy manufacturer. Some have teasingly called it My First Soldering Iron, but its a quality tool that will likely last you a lifetime of hobby soldering or years of production work.

Im a light hobby user, so this product is probably overkill, but when I needed to source new elements and tips for my Weller pencil-type irons, I decided to consider a controllable station instead. The FX-888 heats up quickly (MUCH faster my old Weller irons), and provides great results. The adjustable temperature allows me to use one tool for various tasks, and tips are readily available. The cord connecting the iron to the controller is very supple, so moving the pencil around while working is easy. I just wish they had considered this for the power cord, as its quite stiff. The base is sturdy and well-weighted, and the built-in cavity for the wire-mesh iron cleaner is a plus. One drawback is the lack of a power on indicator. The flashing ready light is in a poor position for visibility, and can be easily missed if you look at just the right (wrong?) time. I will be adding another LED in the top of the unit. Im also not keen on the brightly-colored and contoured appearance of the unit, but styling is subjective. Id also prefer the holder and controller be joined units for easier portability, but this is a minor inconvenience. Overall, Im very satisfied with the unit, and am pleased with the purchase. SUMMARY: PROS: Heats quickly Good range of temperature adjustment Wide selection of tips available Flexible iron cord Sturdy base with tip cleaner CONS: Fisher-Price styling Controller and base are separate units No power-on indicator Poor Heating LED placement Stiff power cord

Sturdy well made unit and easy to use.

Update to original review: Ive pulled my old Weller back out of storage. The specific issue is that this Hakko isnt nearly as good for soldering quad copter power leads. The leads tend to be 12 or 14 gauge (I match the leads on the battery I intend to use). It is the ground wires that are most difficult because the circuit boards tend to have heavy ground planes. Sure, I can do the job with the Hakko, but it got annoying after the Nth time. That old Weller makes it fast and easy. Sadly, I hear that the new Wellers dont match up to the old ones. Other than those power leads, almost everything else I do is a lighter job for which the Hakko works fine. ------- Its amazing how the price of these things has changed over the years. This Hakko is replacing my 30 year old Weller. That old Weller doesnt have temperature adjustment and its one temperature was dropping. It was time for a replacement. This Hakko station does everything I want and that brass wool thing is great for tip cleaning. Still getting used to the adjustable temp though. Basically though. its a soldering iron. No surprises there. Flip the switch, it gets hot, melts solder, etc. No drama. The soldering iron is more like a pencil. No problem because it gets hot fast and gets the job done. If I were doing a lot of soldering - as in it were my job, Id have probably gotten another Weller but with adjustable temp. They are more industrial and my old one lasted me 30 years. Thats a strong recommendation. For now, though, I may solder for a few hours on the occasional weekend when Im assembling a quadcopter or arduino gadget. No need for the expensive industrial tooling.

Ive been soldering for about 55 years and am an electronic hobbyist. In the 50s, I had a Weller gun. It looked like a gun, had a trigger like a gun and worked fine on radios and TVs that I worked on. As electronics got smaller and more sensitive to overheating, I switched to a Weller or Unger iron. I think one has since bought the other. These irons and 1/8 tiplets served me very well for many years. The only problem was that the tiplet would eventually break and need replacement. They are threaded but it is impossible to get the old one out unless you drill it out. Too much work so I just bought a new heating element and put in a new tiplet. My tiplet broke and I decided to search the internet. Perhaps someone had by now figured out a way to replace the tiplet without drilling. No luck, but I kept seeing replies that essentially said toss your Unger and get a Hakko soldering station. If youve looked at soldering stations, you will see that prices are all over the place with some too expensive for a simple hobbyist like me. I think you could find something for less but then I dont know if it would be as well rated. So, I purchased this unit. I really dont need precise temperature calibration so I just set the dial in the middle. The reason that I like temperature regulation is that the the iron heats up extremely fast, about 15 seconds to melt solder. Im so old that I cant afford to wait 3 to 5 minutes just to solder one joint. Temperature regulation also ensures that the iron wont cool off if you have several joints to solder. I also like the very small handle and very flexible cord. The smaller handle gives you better control when you have to very accurately position the tip. It wasnt clear which tip the unit came with so I ordered a D16 chisel point separately. I was afraid it would come with a pencil tip which I dont like because its sometimes hard to put enough heat into the joint. It did come with the small chisel tip I prefer so I should have waited to order the extra tip. The two tips will outlast me, Im sure. Lastly, the base unit comes with a sponge and a metal cleaning wire which looks like a cross between a Brillo pad and a wad of metal shavings. This seems to work pretty well. Ive always just used paper napkins to remove excess solder and clean the tip. This is not a perfect process as sometimes solder goes places where you wish it wouldnt. Like, I have a solder-splash shaped tatoo on one foot. The quality of this unit looks very good on the outside. There is an article online which shows how to modify this unit so that the light on front indicates ON as well as Tip Heating. As it is, the light only shows when the tip is heating so one might be concerned about leaving the unit on because there isnt an ON light. I wont make this mod because Im very careful about leaving stuff powered. The point here is that the article gave me a chance to see what the guts of the base unit looked like and it also looks to be of high quality. Soldering is not that hard, but there is a learning curve. I would recommend this unit to beginners as well as experienced solderers because it just makes it more easier to make precision joints where connections are closely spaced and parts are more heat sensitive. If youre just soldering railroad track together, you dont need this. For IC and microprocessor work, this unit will save you time by not having to rework cold or bridged joints.

This station oozes quality. The material used for the iron holder and the control housing is top notch. The holder is solid metal and the control housing shell seems to be some type of plastic. It is built like a brick, and should withstand a good beating. While it does look a little Fisher-Price, the shade of blue is actually a bit darker when looking at it in person, so it looks better than in the picture. The build quality more than makes up for the color. The holder has two mating pieces, so you can clean inside it or replace the metal cleaning ball, then easily put it back together into a solid assembly. My only complaint would be the sponge. It could mate better with the holder for it, but maybe it will be better when wet. In any case, it shouldnt matter, as it doesnt take much pressure to clean a tip. It started up fine on the first try, and quickly heated the tip. It came with the chisel tip, the T18-D16, which is kind of small at 1.6mm in diameter, but it provides better heat transfer than a conical tip, and should be easy to work with in fairly tight board layouts. I might recommend buying a few larger tips for larger components, as I did. I look forward to working with it, seeing all the positive reviews. Your tip might smoke a bit on the first use, but that is normal, as they are usually coated with a protective layer for storage.

While I had read all the really good ratings and heard good things about this brand and model, I was surprised how sturdy everything was.