Hakko FX888D-23BY Digital Soldering Station FX-888D FX-888 (blue & yellow)

The soldering iron was a little skinny to hold but performance was more of a deciding factor. When applied to the workpiece the iron was unable to maintain heat transfer and was not useful. I was unable to measure actual power draw. The two piece design is thoughtful and allows for flexibility in placement of the iron

We have two Hakko 936-12 irons, which we use in a daily production environment. The FX-888 is the updated replacement. Its smaller, but packs a bit more power than the 936. The handpiece is comfortable for day-long use and the new holder incorporates a slot for brass wool (better than a wet sponge), so you dont need a separate tip cleaner. Theres still a sponge plate for traditionalists. Hakko supplies both a sponge and a wad of brass wool. The thermostatic control is accurate and the iron heats quickly. More important, the more powerful 70W ceramic element brings the tip back up to temperature quickly when you heat a large surface, and the internal thermostat prevents overshoot. In other words, the Hakko maintains your chosen working temperature, making it easier to do clean, consistent work. Using brass wool to clean the tip causes less thermal shock than water does and theres essentially no thermal recovery time. The supplied screwdriver-shaped tip is small enough for standard printed-circuit board work and can also lay down enough heat to attach a braided ground to the back of a potentiometer. The silicone-coated cable on the handpiece withstands occasional accidental contact with the tip or barrel without damage. The brightly colored components are a departure from the usual somber black, looking like they could have been made by a toy manufacturer. Some have teasingly called it My First Soldering Iron, but its a quality tool that will likely last you a lifetime of hobby soldering or years of production work.

The price on this unit was more than I usually like to pay, which is why Ive struggled most of my life with inadequate soldering irons. But one day, while trying to take some capacitors off a circuit board, holding the iron on there endlessly in frustration, I decided enough was enough. I scoured the reviews in Amazon, initially looking at a Weller unit, but someone pointed to the Hakko unit and I was impressed by the number of positive reviews. So I plunked down my hard-earned cash, and waited. One week later, I unboxed the unit, noticing the solid construction. And after trying it, I knew I had reached soldering iron nirvana! Here are the features I really appreciate: 1. Hot in seconds flat. Theres a little red LED on the front that tells when the iron is heating. When it goes off, the tip is ready. I didnt time it but turning the heat dial up half-way only takes about 5 to 10 seconds before the tip is ready. Wow! so different from what I was used to. 2. Performance. Most soldering can be done at about half temp. A few times Ive cranked it up all the way, to melt some stubborn joint, and it really works! 3. The brass tip cleaner. I really like the little brass wool that you can rub the tip on. It works very nicely and is much more convenient than water/sponge (although you can use that too). 4. Good stand. Its solid and doesnt fall over easily. Same with the transformer-temp control unit...its really heavy. 5. Flexible cord. Dont you just hate it when you get a tool that has a stiff plastic cord that never seems to straighten out? Well this one doesnt have that. The cord from the iron to the controller is nice and flexible. 6. The heating takes place so quickly that as soon as Im done a joint and have a break, Ill just dial the temp down and leave it on low, knowing that I can get it back up in less than 10 seconds. Im sure that helps the tip last longer. Theres really nothing not to like about this unit. Well, the tips are a bit expensive (about $10), but they look like they will last a while. Ive also seen some sets of tips on eBay for less...not sure about the quality of these though. Im in my early 50s now, and am a bit ashamed that Ive been doing occasional electronics work for about 30 years without such a good tool. Im pretty sure, unless my unit suffers from a defect, that this will be the last soldering iron I buy for the rest of my life. Should have bought it a long time ago...

Its a workhorse in my shop. Nothing else to say.

So happy with this purchase, always got cheap soldering irons thinking I can replace it if needed and Im no soldering expert so dont use it that often, so might as well go under $50. As I was about to purchase my 4th iron (which would have taken my total spent on soldering irons to around $150) I decided to take a chance and spend the money to get a Hakko. The unit is much smaller than I anticipated (size didnt matter to me so never looked at dimensions) which is great, it is very easy to tuck out of the way. Saw some people dont like the separate iron stand, but personally that is the best for me. The station and stand can sit in the corner under my monitor at all times and I can just pull out the stand when I need to solder and I dont have to worry about any heat affecting my monitor. And the stand itself is all metal and feels quality. Time will tell with the sponge, saw some people not liking it, but havent run into anything myself as of yet. Heat up and temp stabilization are crazy fast, coming from cheap units this one surprised me when I first turned it on, was used to turning on the soldering iron and then in a few minutes could expect it to be stabilized. With the Hakko I turned it on and stood up expecting to have some time, and I wasnt 10 feet away by the time it hit temp and was almost stabilized. So very fast, which shouldnt be surprising if you have only been using the cheap units. Lastly is the interface, that was the thing I saw in reviews that made me almost not get this unit which would have been a mistake. Like I said I am not a good solderer by any means, so for me I tend to have 1 type of solder wire and keep the iron at the same temp almost always. If I changed temps regularly I would take the time to set up the presets to the temps I use most frequently. In my situation though, pressing the enter button and then adjusting the temp takes maybe 10 seconds and is done very infrequently. The interface is similar to another item I own where you press enter to start adjusting the temp and then the arrow to change the number, so for me it made immediate sense on what buttons to push. For anyone that intuitively thinks they should press the arrow to change the temp, I would highly recommend writing on the unit itself so you know what to do. Even a simple 1 and 2 to know which to press first would do it for you. But really that is how the system works, press Enter and the first digit flashes so you can press the arrow to change that digit, press enter again to go to the next digit, repeat till you have the temp you want. Unless you need an exact temp, you will never change the last number away from 0, so you will just change the first or second digit. Most times I am changing it up/down in hundreds so I just change the first digit and then hit enter twice to skip the next to digits. Anyone even remotely tech savvy or under a certain age will be totally fine with this, the only way the interface is an issue is if you are constantly changing temps, and even then it depends on the temps you are using and how many different temps since you can set custom presets to switch between. Will update this review if any issues arise, I expect to never have to buy another soldering iron in my life, so will definitely adjust this review if that turns out not to be the case.

Not a soldering guy, but I wanted to try my hand at a semi advanced job attaching a ribbon cable to an smb to an n64. Used my 20$ soldering iron...BIG MISTAKE. completely botched the job, my iron wasnt able to keep a consistent temperature and my cheap solder immediately stuck many legs together. Tried to save it but ended up reading more about the appropriate tools. Well... a few practice rounds later with the dead n64 an it so crazy how different using this soldering iron is. Expensive, but holy moly does it do a good job and Temps are amazingly stable.

It was fine but I ended up replacing it with a pinecil, which is less bulky, way more controllable, and has all sorts of cheap tips available.

Im a light hobby user, so this product is probably overkill, but when I needed to source new elements and tips for my Weller pencil-type irons, I decided to consider a controllable station instead. The FX-888 heats up quickly (MUCH faster my old Weller irons), and provides great results. The adjustable temperature allows me to use one tool for various tasks, and tips are readily available. The cord connecting the iron to the controller is very supple, so moving the pencil around while working is easy. I just wish they had considered this for the power cord, as its quite stiff. The base is sturdy and well-weighted, and the built-in cavity for the wire-mesh iron cleaner is a plus. One drawback is the lack of a power on indicator. The flashing ready light is in a poor position for visibility, and can be easily missed if you look at just the right (wrong?) time. I will be adding another LED in the top of the unit. Im also not keen on the brightly-colored and contoured appearance of the unit, but styling is subjective. Id also prefer the holder and controller be joined units for easier portability, but this is a minor inconvenience. Overall, Im very satisfied with the unit, and am pleased with the purchase. SUMMARY: PROS: Heats quickly Good range of temperature adjustment Wide selection of tips available Flexible iron cord Sturdy base with tip cleaner CONS: Fisher-Price styling Controller and base are separate units No power-on indicator Poor Heating LED placement Stiff power cord

Great products !!!

I have one of these that finally broken down after 6 years of daily use. Replacing the soldering iron wand part was nearly the same as buying a new one, so I just bought a new one. And I couldnt be happier, Hakkos gear is just as solid as its always been. People complain about the temperature control interface and I get it -- its awkward. I dont need to change temps a lot so its fine, but if you do you change temperatures frequently you may want something else. If youve used cheap soldering irons because you couldnt quite justify the cost, Ive been there too, and I can assure you its worth it to get a quality soldering iron. You can go faster, the work comes out more consistent, and youre never fighting with the equipment.