LIAN LI High Airflow Micro ATX PC Case, RGB Gaming Computer Case, Mesh Front Panel Mid-Tower Chassis with 2x140mm ARGB PWM Fans Pre-Installed, Tempered Glass Side Panel (LANCOOL 205M MESH, Snow)

This chassis is beautiful, nice design. Have nice filters with magnets, easy to manipulate with. There are also many ways to arrange the fans inside. I give it 4 stars because the interior is not designed the best. There is separate compartment on the bottom for power unit and hard disks. The cover that separates it with the rest of chassis, has only two holes to use for moving cables around. Both are close to the motherboard (once installed), and one hole is really impossible to use since the power unit will cover it. Speaking of it, make sure you do not buy power supply with rgbs since the fan will be facing bottoms. Unless you lie the tower sideways, there is no use for rgb power supply. The rest of components were easy to install (motherboard, AIO, memory, gpu..)

I like the simple design of this case. Instructions/ manual is a bit lacking in cretin areas you sometimes have to look at what screws do what because the manual can be a bit vague. Careful if you are doing a vertical gpu with a full length card it can be a bit tight xD. Keep in mid as it is a little deceiving on the length of the case. Its taller then it is long, surprised me a little bit but i still love it. Tips: You may have to slide the hdd cage towards the front more then when it arrives if you have a longer PSU. if you have hdds you might have to mount them towards the glass unless you have some 90* sata cables. Keep you cables managed in the back there is JUST enough room to route cables (reason for 90* sata)^

Great case good looking acceptable cable management on the back, good pass through locations. Came with all necessary hardware. only comment is the rear exhaust fan can only be 120 mm fan which is fine i just happen to buy 140mm fans but it comes with 2 120mm fans seem quite and good so i just used my 2 140s as intake and the 2 120s as exhaust (PC has been built for 1 month so, 1 month review) good overall Side note for new pc builders the cables coming from the case audio and power button need to be split and go to 2 different places on the motherboard. I didnt know that so my PC didnt power on because I didnt have the power buttons plugged into the motherboard beginner mistake but the cables are not labeled if i remember correctly so thats why i mention it

Originally, I had intended to get the Corsair Crystal 280x, A nice, easy to assemble, and cable manage micro-atx case. However, I found this case right before I was about to order that case, and I am extremely glad I did. -For starters, the price is cheap- 70$ at the time of purchase, which is less than half than the Corsair Crystal 280x. For this price, you get exceptionally high build quality. All panels (all high-quality aluminium and tempered glass) fit perfectly and feel solid, as well as easily attach to the case. It comes with magnetic dust filters for the top and front of the case -Airflow is exceptional, and exhaust/intake restrictions are very little/none. My temps have dropped by 2-4 degress since implementing this case compared to my previous case (using corsair fans, not the stock fans). I had to mount my 240mm radiator for my AIO at the front of the case, as I could not get my fans and radiator to clear my RAM when mounting at the top. Even then, this likely varies from motherboard to motherboard. -The size! Its incredibly small, while maintaining easy part compatiblity (Ive seen builds with 3080s fitting, no problem) Its still very easy to build in as long as you use a modular PSU, and you should. Its about the same height as other micro-atx cases, but much thinner. It having a basement certainly helps with the cable management. At the end of the day, I would reccoment this case for anyone building a Micro-ATX system, Id even go as far to say this is the best bang-for-the-buck case option, maybe even the best in general. In Short: -Amazing Price -Looks Great -High Quality Build -Easy to Build in with Modular PSU -Fits most GPUs -Just get it

Great case if youre going for an AIO to cool, but if youre going air cooling you may want to look for a different case. as the front panel is very closed off and thus restricts airflow. Also, it does not come with all the fans needed. you will need to buy more for the top. I had to buy 2 140mm fans for the top. I was able to get the NZXT Kraken 280mm AIO to fit in the proper orientation in the front panel. Its a very very tight fit though, but it does fit. The 280 did not fit in the top of the case as it hits the motherboard. so you may want to look at a 240 for the top of the case. The Asus 3070 fits as well. Might be a little tight with a 3 fan card with the AIO in the front, but you will have to test that on your own. Great cable management in the back of the case and underneath as well.

Ive purchased Lian Li in the past and theyve been nothing but exceptional. This is case is so close but there are a few issues I have with it. 1. The motherboard mounting posts and screws didnt fit together. The posts screwed into the case just fine, but when I tried to secure the board, the screws didnt fit. Luckily I hoard old computer parts and bits and had a bunch of old ones that fit. They werent black, but you wont see the posts beneath the mobo, really. 2. Not a huge issue, but I dont see how one can mount an 240mm aio (all in one) cpu cooler to the top. The motherboard heat sinks dont seem to clear it. However it will mount to the front of the case. My aio cooler is EVGA CLC 240mm All-In-One RGB LED CPU Liquid Cooler. Outside of that I love the case, its mATX and can fit miniITX if thats your thing. Plenty of clearance for a gpu (I have a 3070.) Fits a regular sized PSU. A good clean look for a modern build.

this is an amazing budget tower case. i had been looking at the corsair tower case for my build but went for this one instead and it’s been amazing and does its job. only reason i give this 4 stars instead of five is because my glass panel had shattered into pieces when i had tried to take it off a couple weeks after i finished building my pc. it was relatively easy to find a replacement panel but it really bummed me out

This is definitely a good value case. Everything was easy to install with room to spare, granted I dont have much in there right now. Tempered glass is nice, make sure to remove the cellophane stuck to it. My only real complaints have to do with the front panel. It just snaps in without any screws, picking it up once I almost dropped it because the panel popped out so be careful. I cant say the mesh dust filters do much either, still getting a ton of dust sucked into the case. Overall happy with it however.

When I bought this case, I was worried the great looks I saw in the thumbnail would be a front of a crappy poorly designed cheapo looking product in real life. I was pleasantly surprised to find the case lives up to its great looks and has a great build design. I really like the harddrive and power supply bay, as it just makes the build clean and keeps the clutter away from the view through the glass panel.

I ordered this case to upgrade the airflow to my pc as well as get some rgb into my setup. After installing my computer into the case, the rgb on the fans decided to stop working. It was clearly a problem with the fan controller on the back of the case. I decided to give the case another try and buy another one and return my faulty one. This time after installing my computer into the case, the rgb worked fine but the rgb controlling buttons on the front panel are faulty. The only reason why I’m not returning this one also is because I don’t want to go through the hassle of buying another case and swapping it over again. The Lconnwct software is a joke and doesn’t work with the case. I suggest you look for another case if you planned on buying this one. I will most likely never be buying a Lian li product again.